Getting Started with Plumber's Essentials When Installing a Bathtub
Getting Started with Plumber's Essentials When Installing a Bathtub
Blog Article
Just how do you really feel in relation to Installing A Bathtub?
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard task. If the old bathtub is conveniently easily accessible, the task can relocate quickly; if you need to open up a wall to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the brand-new one. See to it you have certified yourself for the work as well as are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to take into consideration employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will certainly aid you set up a new bathtub in your washroom if you have currently purchased a brand-new bathtub as well as do not require to transform the setup of your previous water pipelines.
Your devices and also product list should comprise the following:
Getting ready for the Installment
To start with, the sustaining framework provided with the bathroom must be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets device to avoid pressure on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipes have been removed, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wood boards under its feet, place the tub in the needed placement. The wooden boards are helpful in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the tub until the level checks out degree.
To set up taps, fit all-time low of the outermost flexible tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and the regular outlet for leaks.
Finally, deal with the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has been made use of a minimum of once as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making certain that the washers are in location between the faucet and the sink. Secure the faucet in position with the maker supplied backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous kind must be attached to the faucet ends first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are marketed in tubes and cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can split rather very early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads about How to Install a Bathtub, I think sharing that piece of content was a good idea. Appreciated our review? Please share it. Help other people discover it. Thanks for your time spent reading it.
Click Here Report this page